Home arrow Forums



Go Back   XS11.com Forums > Idle Talk Forum > XS11/XJ11 Discussion

Reply
 
Thread Tools Display Modes
  #1  
Old 10-01-2011, 06:26 PM
Ebenezer Ebenezer is offline
XSive
 
Join Date: May 2011
Location: Hawley, MN
Posts: 67
Carb kits?

Thinking about going through my carbs this winter. Had a stuck float this summer and the two I took off definitely needed a cleaning. No major problems since, but they at least could use a good cleaning. Once the bike runs for about a minute on choke or half choke it starts popping. Turn the choke off and it runs fine. Have synched it with the carb tune but it still pops when choked.

Is the best place to get carb kits Georgefix? Or am I going overboard by putting kits in all four? Just thought it would be easier to do it over the winter than having to rip it apart in the summer. What do you guys think?
__________________
Ryan

1981 XS1100SH
K&N filter
Spade fuse block
Barnett Springs
Reply With Quote
  #2  
Old 10-02-2011, 06:53 AM
Aches n Pains's Avatar
Aches n Pains Aches n Pains is offline
XStremely XSive
 
Join Date: Sep 2009
Location: Reston, Va.
Posts: 346
I like Georgefix very much.

However, I have found that most of the time a good cleaning will do the job. Be very careful with the diaphragms and the float bowl gasket as you disassemble. There are lots of good posts here and on the Suzuki forum re: working on these carbs.

There is a particularly good .pdf tutorial on: http://members.dslextreme.com/users/bikecliff/

Scroll down on the page and look for Mikuni BS(CV) Carburetor Rebuild Tutorial. It has a rotating NEW in front of it. It is for carbs off a Suzuki but they are, essentially, the same layout (BS34 carbs).

Aches n Pains
__________________
1995 KZ100P
Pods, jets, pipes, cam adjuster, oil cooler

1977 Ironhead - custom build
Hot engine, custom frame, KZ front and rear, high torque starter, alternator conversion, Progressive shocks, Thunderheart wiring, Dyna ignition, oil cooler, Dakota Digital instruments, etc.

Sold all my XS's to Eastcoaster but still love to keep up with you guys. This is the best cycle forum on the web.
Reply With Quote
  #3  
Old 10-02-2011, 07:23 AM
BA80's Avatar
BA80 BA80 is offline
Doctor of XSology
 
Join Date: Oct 2010
Location: Tulsa, Ok
Posts: 9,861
Reuse your original jets and just get the needle and seat and bowl gaskets. Most aftermarket are not correct and don't work well.

http://www.carbkitscapital.com/carb_...a&model=XS1100
__________________
Greg

Everybody is a genius. But if you judge a fish by its ability to climb a tree, it will live its whole life believing that it is stupid.

― Albert Einstein

80 SG Ol' Okie;79 engine & carbs w/pods, 45 pilots, 140 mains, Custom Mac 4 into 2 exhaust, ACCT,XS850 final drive,110/90/19 front tire,TKat fork brace, XS750 140 MPH speedometer, Vetter IV fairing, aftermarket hard bags and trunk, LG high back seat, XJ rear shocks.

The list changes.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 10:21 AM.


Powered by vBulletin® Version 3.7.3
Copyright ©2000 - 2022, Jelsoft Enterprises Ltd.
Integrated by BBpixel ©2004-2022, jvbPlugin